Aeration membrane bubble tube diffuser

Aeration membrane bubble tube diffuser

Diameter: Φ65  Length: 500—2000mm
Tube diffuser technical data

Tube diffuser design and installation

1,When the tube micro-porous aerator in application,in the bottom of the aeration tank, the tube diffusers on the intake manifold generally spaced 500-2000mm. Aerator and aerator about the general spacing of 500-1500mm; depending on the water concentration, gas supply and other process conditions.

2,The arrangement of tube diffusers is based on the air flow rate which can be calculated according to the length of the aeration tank and the size of the bottom intake manifold.

3,The bottom of the intake manifold to be apart from the tank shore main pipe, and install a valve. welding a flange bending by the pool wall 500-600mm from the bottom of the aeration tank , and coupled with rubber gaskets and screws.

4,Tube diffusers to install 150-250mm from the bottom.

5,Each intake pipe from the pool wall down connected to the bottom of the intake manifold, connect one or more.

6,The aeration tank bottom should be flat.

Aeration tube diffuser inlet manifold flange sketch map

Bottom air intake pipe installation of one or more connections diagram

If you need more infomation of tube diffusers, welcome to contact with me.

Email: rita@sintafrp.cn
Whatsapp: +8618932935537

Demister/Mist eliminator

PP mist eliminator

Demister (mist eliminator) is mainly composed of corrugated leaves, plates, clamps and other fixtures. In the wet desulfurization, easy to produce particle size of 10 - 60 microns "fog " in the absorption tower operation process ," Fog "not only contains water, but also dissolves sulfuric acid, sulfate, sulfur dioxide and so on, also causes the fan, the heat exchanger and the flue of the tarnished and the serious corrosion, therefore, Fog requirements, the purified gas before leaving the absorption tower to be demist. Demister nozzle is one of the main components of the demisting system. The defogger nozzle is mainly made of high quality plastic with high wear resistance and long service life.

Demister 2

The demister is used to separate the droplets entrained in the gas in the tower so as to ensure the mass transfer efficiency, reduce the valuable material loss and improve the operation of the compressor behind the tower. Generally, demisters are arranged on the top of the tower. Can effectively remove the 3 - 5um droplets, if set up the tower demister, not only to ensure the mass transfer tray efficiency, but also can reduce the board spacing. Therefore, the demister is mainly used for gas-liquid separation. Also for the air filter for gas separation. In addition, the screen can also be used as a variety of instruments in the instrumentation industry buffer to prevent radio interference, such as electronic jammers.

Water treatment cubic mesh packing

Water treatment cubic mesh packing

Cubic mesh packing has the characteristics of spiral mesh, which can make waste water, air and biofilm full mixing contact exchange. Biofilm cannot only balance stayed on the spiral mesh but also can maintain good activity and its pore variability. In the process of waste water running, gas collide with each other and be cut into smaller bubble network, increasing the utilization of oxygen can reduce aeration, while biofilms have good metabolism does not stick together, so it has the characteristics of bubble cutting ability, larger space utilization , no dead zone , etc. It is the current performance indicators of sewage treatment best filler.

Features

1. The cubic mesh packing material is PP, high temperature resistance, acid-resistance

2. Over-all structure, high porosity, high surface area

3. Hanging membrane fast and easily fall off

4. Water flow in three dimension, no blocking, no clump

5. Light weight, not deformed after long using

6. Can be used as cooling tower fill,good heat-transfer, balance the water distribution

Physical characteristics

According to different fiber density, the filler porosity is 95% to 98%, fiber diameter ? 0.8mm ~ ? 1.5mm, fiber density 0.9 ~ 0.92g / cm3. Bulk density with the shape and porosity vary, usually 9 ~ 20kg / m3. High compressive strength of packing, under water treatment conditions are generally not deformed, under the conditions of loading 400kg / m2 compression deformation of not more than 8%, and is elastic deformation. Adapt to the temperature range of 5 ? ~ 40 ?, if the temperature is below 0 ?, the filler becomes more brittle hardness, impact resistance is poor, you must add special additives, it is generally not used in frozen water treatment.

Product Specifications

specification

 

 

Density (g / cm3)

Wire diameter?mm? Porosity % Surface area?m2/m3? Compressive strength KPa
500*250 ?1 0.6-1.5 96-99 65-75 3.6-4.0
Good oxid film Anaerobic hanging mold
Influent load KgBOD/m3D Biomass dry (dry weight) kg/m3 Biomass (wet weight) kg/m3 Influent load KgBOD/m3D Biomass dry (dry weight) kg/m3 Biomass (wet weight) kg/m3
0.2-1.2 2.18-2.79 190-360 7.4 0.43 106.7

Cooling tower

According to Publisher, the Global Cooling Towers market is expected to grow from $2.27 billion in 2016 to reach $3.36 billion by 2023 with a CAGR of 5.7%. Growing demand for cooling towers from developing regions, technological improvements in cooling towers and increasing demand for HVACR deployments among various industries are propelling the market. However, water requirement in bulk quantities and slow growth of these towers in Europe and North America are hindering the market.

Hybrid towers segment dominated the cooling towers market with a highest market share due to optimal cooling and water conservation. On the other hand, the demand for fiber-reinforced plastic (FRP) is growing rapidly as this material is corrosion resistance, less cost compared to other materials and easy to install. Growing construction projects and rising focus on building energy management technologies are increasing the demand for HVAC cooling towers. These cooling towers are widely used in industrial applications to maintain temperatures in chillers.

Asia Pacific has acquired largest market share owing to the adoption of cooling towers in industrial sector. Demand for cooling towers is also growing in China with the emergence of new power plant projects and rapid industrialization.

Materials Covered:
-Concrete
-Fiber-Reinforced Plastic (FRP)
-High-Density Polyethylene (HDPE)
-Wood
-Steel

Applications Covered:
-Chemical
-Power Generation
-Petrochemical and Oil & Gas
-Food & Beverage
-HVACR
-Pharmaceutical and Laboratories
-Process Cooling

Method of Heat Transfers Covered:
-Plume Abatement Tower
-Dry Tower
-Water Conservation Tower
-Evaporative Tower
-Other Method of Heat Transfers

Constructions Covered:
-Factory Assembled
-Field Erected

Type of Towers Covered:
-Hybrid Cooling Tower
-Closed-Circuit Cooling Towers
-Open-Circuit Cooling Towers
-Natural Draft
-Mechanical Draft

Spiral Diffuser

Spiral Diffuser

Spiral diffuser is a new aeration devices ,in the spiral aeration ,casual flow-flow ,SH-Aerator on the basis of a new type of improved aeration devices ,the product is resistant to corrosion ,Oxygen utilization of high and difficult to plug and easy installation ,and other major features . Spiral diffuser for the use of multi-slice cutting patterns for aeration and oxygenation ,when Francis entered the air-Aerator ,the airflow through the first two spiral cutting system ,cutting into the lower deck of the multi-storey sawtooth-cloth .The first ,multi-cutting ,so that cutbubble bubble ,this has greatly enhanced the utilization of oxygen ,a gas uniform cloth ,and oxygenation efficient characteristics.

Application: A. aeration tank in industrial and urban wastewater treatment plant, which uses blower as air source. B. activated sludge method and contact oxidation method. C. the technology renewal and reconstruction of existing old aerator.

Technology advantages: 1. adopt big holes to exhaust gas and lead flow, use several structures to cut and scatter airflow; its a modern and advanced aeration-diffusion method. 2. the equipment has characteristics of non-blocking and small air resistance, which can keeping producing air bubbles evenly and densely. Compared with micro-pore aerator, its efficiency wont deteriorate gradually. 3. the material adopted wont age easily, guarantee measures are complete, cleaning, replacing and repairing are not needed. 4. resitance loss is small, ?30Pa. 5. aeration device often takes blower running at a low pressure to supply air, the smaller the resistance is, the higher the efficiency will be.

Choose tube settler for wastewater treatment

Choose tube settler for wastewater treatment

PVC tube settler media and PP inclined tube sheet. The hexagonal honeycomb slope tube produced by our company uses EPR copolymer plastic as the material,it was hot drawn into hexagonal tube by a infrared thermal machine,and then using patented technology and high frequency to weld into a whole product,our staff will carry on-site installation for the customer.Inclined tube is mainly used for a variety of precipitation and sand removing.For a decade,it is a water treatment device that's widely used in the drainage works.It has the advantages of being suitable for a wide range,high treatment efficiency,small footprint. PVC lamella sheets, tube settler in wast water treatment application: 1. Retrofit existing clarifiers and sedimentation basins with tube modules to increase settling capacity and increase through put. 2. Provide replacement tube modules for existing installations.Our Environmental designs and builds liquid cleaning and recycling equipment including. 3. Circular Clarifiers. 4. Parallel Plate Settlers. 5. Tube Settlers. 6. Horizontal and Vertical Clarifiers. 7. Air Strippers. 8. API Separators. 9. Oil Recovery Units. 10. Complete Engineered Systems. If you have any questions or interests, pls contact: rita@sintafrp.cn Whatsapp: +8618932935537

MBBR bio filter media introduction

MBBR bio filter media introduction

MBBR is the abbreviation of Moving Bed Biofilm Reactor. It is a novel biologically active carrier.

MBBR media adopts scientific formula, depending on the nature of water, blending a variety of beneficial microorganisms grow quickly attached trace elements in polymer materials,through a special process modification, constructed, with more than large surface area,hydrophlic, high biological activity, biofilm fast, good effect, good impact resistance.

MBBR process is a kind of sewage treatment process developed by Kaldnes company and SINTEF research institute, which absorbs the advantages of traditional fluidized bed and biological contact oxidation process, and has good nitrogen and phosphorus removal effect.

At present, the process has been successfully applied in industrial waste water and domestic sewage treatment.

Our MBBR bio filter media's material is HDPE, 100% virgin material.Besides K1, K3, K5 media, we also have other sizes such as PE01(12*9mm), PE02(11*7mm), PE04(16*10mm), PE08(5*10mm) as below shows:

With many production lines, we can deliver our goods in short times and can meet customer's requirements.

Thanks for your viewing and if you have any requirements about our products,welcome to contact with us any time.

Email: rita@ppfill.com

Cooling tower drift eliminator

Cooling tower drift eliminator

Drift eliminator are an important part for the cooling tower.

Functions of drift eliminator as below shows:

1. Drift eliminator can control the water loss.

2. Make the drift fast with low presssure drop.

3. Long-time service and cost efficiency.

Drift eliminator are used to control water loss for the cooling tower. Different cooling tower use different drift eliminators. What we have are Marley drift eliminator, EAC drift eliminator and other types.

Material: PP and PVC Our drift eliminator are designed to make the maximum drift removal effciency in both crossflow and counterflow cooling tower applications. Size are customized according to buyers, welcome your inquiry.

Email: rita@sintafrp.cn

Contact Info

No.282, Zhonghua street, Xinhua district, Shijiazhuang city, Hebei province, China

Tel: +86 0311-85335605

Fax: +86 0311 85335605

Phone: +8618931991958/+8618932935537

Email: rita@sintafrp.cn

Skype:Ritadu

 

 

Daily: 8:30 am - 6:00 pm
Sunday: Closed

Copyright 2016 © All Rights Reserved